1. ALL MECHANICAL EQUIPMENT AND SYSTEMS SHALL BE INSTALLED IN ACCORDANCE WITH THE OREGON MECHANICAL SPECIALTY CODE LATEST EDITION, AND ALL LOCAL & STATE CODES. 2. ALL PLUMBING EQUIPMENT AND SYSTEMS SHALL BE INSTALLED IN ACCORDANCE WITH THE OREGON PLUMBING SPECIALTY CODE LATEST EDITION, AND ALL LOCAL & STATE CODES. 3. ALL MECHANICAL AND PLUMBING EQUIPMENT SHALL BE INSTALLED PER THE MANUFACTURER'S RECOMMENDATIONS. 4. MECHANICAL CONTRACTORS SHALL RECEIVE PRIOR APPROVAL FROM THE STRUCTURAL ENGINEER BEFORE MAKING CUTS THROUGH ANY STRUCTURAL MEMBER. 5. MECHANICAL CONTRACTORS SHALL COORDINATE INSTALLATION WITH CONSTRUCTION SUPERVISOR AND WITH ALL OTHER TRADES TO AVOID CONFLICTS. 6. THE MECHANICAL CONTRACTORS SHALL VERIFY MOTOR VOLTAGES WITH THE ELECTRICAL DRAWINGS BEFORE ORDERING MOTORIZED EQUIPMENT AND CONTROLS. 7. SEE SHEET M-? FOR SCHEDULED CAPACITIES OF ALL MECHANICAL EQUIPMENT AND MATERIALS SPECIFIED. 8. DOMESTIC WATER SERVICE IS PROVIDED WITH A DOUBLE CHECK BACKFLOW PREVENTER. 9. ALL MECHANICAL EQUIPMENT TO BE PROPOSED MUST BE ON THE APPROVED LIST PRIOR TO SUBMITTALS. ALL APPROVED MANUFACTURERS MUST BE CAPABLE OF MEETING THE REQUIREMENTS OF THE SPECIFIED EQUIPMENT. 10. RUNOUT AND HOOKUP SIZES TO INDIVIDUAL PLUMBING FIXTURE CAN BE FOUND ON THE PLUMBING FIXTURE SCHEDULES, SHEET P-?. 11. PROVIDE REMOTE CEILING ACCESS BALANCE DAMPERS WITH CONCEALED CHROME PLATE COVERS FOR BALANCE DAMPERS LOCATED ABOVE HARD CEILINGS. 12. PAINT ALL VTR'S, FLUES, EXHAUST CAPS, AND OTHER MECHANICAL ITEMS ON THE ROOF TO MATCH THE ROOF COLOR. 13. INSULATED FLEXIBLE DUCTWORK MAY BE USED FOR RUNOUTS TO GRILLES AND DIFFUSERS, IN LENGTHS OF 6'-0" OR LESS. 14. MAINTAIN MINIMUM OF 10'-0" DISTANCE BETWEEN ALL FRESH AIR INTAKES AND EXHAUST OR GAS FLUE DISCHARGES. 15. THE PLUMBING CONTRACTOR IS RESPONSIBLE FOR ALL BACKFLOW DEVICES TO BE INSPECTED BY A CERTIFIED BACKFLOW TECHNICIAN BEFORE THE USE OF THE BUILDING POTABLE WATER SYSTEM. 16. LOCATE ACCESS HATCHES SO AS TO PROVIDE OPTIMUM SERVICEABILITY TO EQUIPMENT AND/OR VALVING. SEE ARCHITECTURAL SPECIFICATION FOR TYPE AND COLOR. COORDINATE LOCATION WITH STRUCTURAL & LIGHTING. 17. WHENEVER THERE IS A DISCREPANCY BETWEEN THE RUNOUT DUCT SIZE SHOWN ON THE PLANS AND THAT SHOWN IN THE SCHEDULE, ALWAYS USE THE LARGER OF THE TWO DUCT SIZES. 18. THE CONTRACTOR SHALL BE HELD RESPONSIBLE FOR VERIFICATION OF EXISTING JOB CONDITIONS PRIOR TO BID. NO ADDITIONAL COST SHALL BE AWARDED TO THE SUCCESSFUL CONTRACTOR (OR THEIR SUBCONTRACTORS) AFTER BIDS HAVE BEEN SUBMITTED AND CONTRACTS AWARDED FOR FAILURE TO VERIFY EXISTING FIELD CONDITIONS. DISCREPANCIES BETWEEN ACTUAL FIELD CONDITIONS AND CONTRACT DOCUMENTS SHALL BE BROUGHT TO THE ENGINEERS ATTENTION FOR ALTERNATIVE METHODS OF INSTALLATION PRIOR TO THE BIDDING OF THIS PROJECT. 19. UNLESS OTHERWISE NOTED ALL EXISTING MECHANICAL EQUIPMENT, PIPING, ETC, TO BE REMOVED SHALL BE DISPOSED OF BY THE CONTRACTOR UNDER THIS CONTRACT. THE OWNER SHALL RETAIN THE RIGHT TO KEEP ANY REMOVED ITEMS. 20. ALL DOMESTIC COLD AND HOT WATER LINES IN THE AREA OF WORK WHICH ARE NO LONGER IN USE DUE TO THIS PROJECT SHALL BE REMOVED BACK TO THE MAINS AND CAPPED. 21. HOLES IN EXISTING WALL OR FLOORS SHALL BE PATCHED TO MATCH EXISTING WHERE PIPING, DUCTWORK, ETC. WERE REMOVED OR ADDED DURING THIS PROJECT. 22. DAMAGE TO THE EXISTING FACILITY DURING THE CONSTRUCTION SHALL BE REPAIRED OR REPLACED BY THE CONTRACTOR AT NO COST TO THE OWNER. MECHANICAL ABBREVIATIONS A/C or AC AIR CONDITIONING IFGC INTERNATIONAL FUEL GAS CODE AFF ABOVE FINISHED FLOOR IMC INTERNATIONAL MECHANICAL CODE AHU AIR HANDLING UNIT IPC INTERNATIONAL PLUMBING CODE ASHRAE AMERICAN SOCIETY OF HEATING, REFRIGERATION, AND AIR CONDITIONING ENGINEERS KW KILOWATT AV ACID VENT LINE KWH KILOWATT HOUR AW ACID WASTE LINE L LIQUID REFRIGERANT LINE BTU BRITISH THERMAL UNITS LAT LEAVING AIR TEMPERATURE BTUH BTUS PER HOUR LAV LAVATORY LEED LEADERSHIP IN ENERGY & ENVIRONMENTAL DESIGN CA COMBUSTION AIR LWT LEAVING WATER TEMPERATURE CC COOLING COIL CD CONDENSATE DRAIN LINE M MOTORIZED DAMPER CDR CONDENSER WATER RETURN MAX MAXIMUM CDS CONDENSER WATER SUPPLY MCA MINIMUM CIRCUIT AMPS CFM AIR FLOW RATE (CUBIC FEET PER MINUTE) MIN MINIMUM CLG CEILING MOCP MAXIMUM OVERCURRENT PROTECTION CW DOMESTIC COLD WATER MPG MEDIUM PRESSURE NATURAL GAS CWR CHILLED WATER RETURN CWS CHILLED WATER SUPPLY NC NOISE CRITERIA NFPA NATIONAL FIRE PROTECTION ASSOCIATION DEG or ° DEGREE NTS NOT TO SCALE DIA or Ø DIAMETER DB DRY BULB OD OVERFLOW DRAIN LINE DWR DOMESTIC HOT WATER RETURN OSA OUTSIDE AIR EA EXHAUST AIR PD PRESSURE DROP EAT ENTERING AIR TEMPERATURE PH or Ø PHASE EER ENERGY EFFICIENCY RATIO PRV PRESSURE REDUCING VALVE ESP EXTERNAL STATIC PRESSURE EWT ENTERING WATER TEMPERATURE RA RETURN AIR RD ROOF DRAIN LINE F FIRE SPRINKLER LINE RPM REVOLUTIONS PER MINUTE FCO FLOOR CLEANOUT RTU ROOFTOP UNIT FD FIRE DAMPER FLA FULL LOAD AMPS S SUCTION REFRIGERANT LINE FLR FLOOR SA SUPPLY AIR FPM FEET PER MINUTE SD STORM DRAIN LINE FS FLOW SWITCH SEER SEASONAL ENERGY EFFICIENCY RATIO FT FEET SFD COMBINATION SMOKE/FIRE DAMPER SP STATIC PRESSURE G LOW PRESSURE NATURAL GAS SYM SYMBOL GA GAUGE GCO GRADE CLEANOUT T & P TEMPERATURE AND PRESSURE GPM WATER FLOW RATE (GALLONS PER MINUTE) TEMP TEMPERATURE GWR GEOTHERMAL WATER RETURN TS TEMPERATURE SENSOR (DUCT OR PIPING) GWS GEOTHERMAL WATER SUPPLY TYP TYPICAL HC HEATING COIL UPC UNIFORM PLUMBING CODE HP HORSE POWER U URINAL HVAC HEATING, VENTILATING, AIR CONDITIONING HW DOMESTIC HOT WATER VTR VENT THROUGH ROOF HWR HEATING WATER RETURN V VOLTS HWS HEATING WATER SUPPLY WB WET-BULB IBC INTERNATIONAL BUILDING CODE WC WATER CLOSET IECC INTERNATIONAL ENERGY CONSERVATION CODE WCO WALL CLEANOUT IFC INTERNATIONAL FIRE CODE WH WATER HEATER NOTE: THIS IS A STANDARD LIST OF COMMONLY USED MECHANICAL ABBREVIATIONS. SOME OF THE ABBREVIATIONS SHOWN ABOVE MAY NOT BE USED IN THIS DRAWING PACKAGE. MECHANICAL GENERAL NOTES MECHANICAL AND PLUMBING DRAWINGS LEGEND FLEXIBLE DUCTWORK THREE WAY CONTROL VALVE DUCTWORK TWO WAY CONTROL VALVE DUCTWORK BREAK PRESSURE REDUCING VALVE DUCTWORK OR PIPING RISE GATE VALVE CONCENTRIC SQUARE TO ROUND TRANSITION REDUCER MOTORIZED DAMPER GLOBE VALVE MANUAL VOLUME DAMPER BALL VALVE SPIN-IN FITTING W/ AIR EXTRACTOR AND HAND DAMPER BUTTERFLY VALVE HIGH EFFICIENCY FITTING W/ HAND DAMPER BALANCE VALVE SWITCH CHECK VALVE THERMOSTAT FLOOR CLEANOUT HUMIDISTAT WALL CLEANOUT TEMPERATURE SENSOR GRADE CLEANOUT CARBON DIOXIDE SENSOR WATER HAMMER ARRESTOR CARBON MONOXIDE SENSOR FLOOR DRAIN NITROUS OXIDE SENSOR FLOOR SINK DUCT SMOKE DETECTOR GAS PRESSURE REGULATOR W/ GAS COCK COMBINATION SMOKE/FIRE DAMPER PRESSURE RELIEF VALVE FIRE DAMPER VENT-THROUGH-ROOF SMOKE DAMPER VENT EQUIPMENT CALLOUT SOIL, WASTE, OR SANITARY SEWER TURNING VANES ACID WASTE LINE INTAKE OR EXHAUST ACID VENT LINE DIRECTION OF AIRFLOW STORM DRAIN SUPPLY DIFFUSER ROOF DRAIN LINE RETURN GRILLE OVERFLOW DRAIN LINE EXHAUST GRILLE CONDENSATE DRAIN LINE FLOOR GRILLE DOMESTIC COLD WATER (CW) CEILING EXHAUST FAN DOMESTIC HOT WATER (HW) TEMPERATURE GAUGE DOMESTIC HOT WATER RETURN (HWR) PRESSURE GAUGE (LIQUID FILLED W/ ISOLATION VALVE) TEMPERED WATER (TW) TEMPERATURE SENSOR (DUCT OR PIPING) MEDIUM PRESSURE NATURAL GAS FLOW SWITCH LOW PRESSURE NATURAL GAS STAINLESS STEEL BRAIDED FLEX CONNECTION FIRE SPRINKLER LINE ELASTOMETRIC FLEX CONNECTOR GEOTHERMAL WATER SUPPLY SUCTION DIFFUSER GEOTHERMAL WATER RETURN Y TYPE STRAINER (1 1/2" OR LARGER PROVIDED W/ BLOW DOWN VALVE) CHILLED WATER SUPPLY FLOW DIRECTION CHILLED WATER RETURN DEMOLITION / EQUIPMENT TO BE REMOVED CONDENSER WATER SUPPLY NEW TO EXISTING CONNECTION POINT CONDENSER WATER RETURN (E) EXISTING HEATING WATER SUPPLY (F) FUTURE HEATING WATER RETURN (N) NEW LIQUID REFRIGERANT LINE REDUCED PRESSURE BACKFLOW PREVENTER SUCTION REFRIGERANT LINE DOUBLE CHECK BACKFLOW PREVENTER SLOPE PIPE IN DIRECTION OF ARROW UNION PIPE ANCHOR AIR VENT PIPE GUIDE TRIPLE DUTY VALVE CAP NOTE: THIS IS A LIST OF COMMONLY USED MECHANICAL AND PLUMBING SYMBOLS. SOME OF THE SYMBOLS SHOWN ABOVE MAY NOT BE USED IN THIS DRAWING PACKAGE. M AIRFLOW AIRFLOW S T FCO H WCO S GCO CO 2 CO NO SD -- # AW AV SD D- RD R- 1 OD R- 1 1 CD G- 1 1 TW TS MPG FS G F GWS GWR CWS CWR CS CR HWS HWR L S TOILET 102 ENTRY 103 TOOLS 104 SHOP 101 MECHANICAL 105 12X10 20"Ø 64X56 ZONE 1 2 8 7 6 5 4 3 2 1 D 8 7 6 5 4 3 2 1 A B C D Copyright, Straightline LLC DRAWING NO. A B C STRAIGHTLINE ARCHITECTURE 4521 South Cloverdale Road, Suite 102 - Boise, Idaho 83709 P: 208.991.0855 [email protected]AGENCY & BID ISSUE EASTERN OREGON YOUTH CORRECTIONAL FACILITY EOYCF: 1800 West Monroe, Burns, OR 97720 Date: 5-9-16 Project: BR3 - 1511 Drawn by: MQ Version History: V1.0 530 Center St. NE, Suite 200 Salem, Oregon 97301 OREGON YOUTH AUTHORITY (OYA) Musgrove Engineering 234 S. Whisperwood Way Boise, Idaho 83709 P: 208-384-0585 16-004 EOYCF VOCATIONAL BUILDING & SNOW MELT SYSTEM 5-9-16 M0.0 Mechanical Cover Sheet ZONING PLAN D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D 5-9-16
Transcript
1. ALL MECHANICAL EQUIPMENT AND SYSTEMS SHALL BE INSTALLED IN ACCORDANCE WITH THE OREGON MECHANICAL SPECIALTYCODE LATEST EDITION, AND ALL LOCAL & STATE CODES.
2. ALL PLUMBING EQUIPMENT AND SYSTEMS SHALL BE INSTALLED IN ACCORDANCE WITH THE OREGON PLUMBING SPECIALTY CODELATEST EDITION, AND ALL LOCAL & STATE CODES.
3. ALL MECHANICAL AND PLUMBING EQUIPMENT SHALL BE INSTALLED PER THE MANUFACTURER'S RECOMMENDATIONS.
4. MECHANICAL CONTRACTORS SHALL RECEIVE PRIOR APPROVAL FROM THE STRUCTURAL ENGINEER BEFORE MAKING CUTSTHROUGH ANY STRUCTURAL MEMBER.
5. MECHANICAL CONTRACTORS SHALL COORDINATE INSTALLATION WITH CONSTRUCTION SUPERVISOR AND WITH ALL OTHER TRADESTO AVOID CONFLICTS.
6. THE MECHANICAL CONTRACTORS SHALL VERIFY MOTOR VOLTAGES WITH THE ELECTRICAL DRAWINGS BEFORE ORDERINGMOTORIZED EQUIPMENT AND CONTROLS.
7. SEE SHEET M-? FOR SCHEDULED CAPACITIES OF ALL MECHANICAL EQUIPMENT AND MATERIALS SPECIFIED.
8. DOMESTIC WATER SERVICE IS PROVIDED WITH A DOUBLE CHECK BACKFLOW PREVENTER.
9. ALL MECHANICAL EQUIPMENT TO BE PROPOSED MUST BE ON THE APPROVED LIST PRIOR TO SUBMITTALS. ALL APPROVEDMANUFACTURERS MUST BE CAPABLE OF MEETING THE REQUIREMENTS OF THE SPECIFIED EQUIPMENT.
10. RUNOUT AND HOOKUP SIZES TO INDIVIDUAL PLUMBING FIXTURE CAN BE FOUND ON THE PLUMBING FIXTURE SCHEDULES, SHEET P-?.
11. PROVIDE REMOTE CEILING ACCESS BALANCE DAMPERS WITH CONCEALED CHROME PLATE COVERS FOR BALANCE DAMPERSLOCATED ABOVE HARD CEILINGS.
12. PAINT ALL VTR'S, FLUES, EXHAUST CAPS, AND OTHER MECHANICAL ITEMS ON THE ROOF TO MATCH THE ROOF COLOR.
13. INSULATED FLEXIBLE DUCTWORK MAY BE USED FOR RUNOUTS TO GRILLES AND DIFFUSERS, IN LENGTHS OF 6'-0" OR LESS.
14. MAINTAIN MINIMUM OF 10'-0" DISTANCE BETWEEN ALL FRESH AIR INTAKES AND EXHAUST OR GAS FLUE DISCHARGES.
15. THE PLUMBING CONTRACTOR IS RESPONSIBLE FOR ALL BACKFLOW DEVICES TO BE INSPECTED BY A CERTIFIED BACKFLOWTECHNICIAN BEFORE THE USE OF THE BUILDING POTABLE WATER SYSTEM.
16. LOCATE ACCESS HATCHES SO AS TO PROVIDE OPTIMUM SERVICEABILITY TO EQUIPMENT AND/OR VALVING. SEE ARCHITECTURALSPECIFICATION FOR TYPE AND COLOR. COORDINATE LOCATION WITH STRUCTURAL & LIGHTING.
17. WHENEVER THERE IS A DISCREPANCY BETWEEN THE RUNOUT DUCT SIZE SHOWN ON THE PLANS AND THAT SHOWN IN THESCHEDULE, ALWAYS USE THE LARGER OF THE TWO DUCT SIZES.
18. THE CONTRACTOR SHALL BE HELD RESPONSIBLE FOR VERIFICATION OF EXISTING JOB CONDITIONS PRIOR TO BID. NO ADDITIONALCOST SHALL BE AWARDED TO THE SUCCESSFUL CONTRACTOR (OR THEIR SUBCONTRACTORS) AFTER BIDS HAVE BEEN SUBMITTEDAND CONTRACTS AWARDED FOR FAILURE TO VERIFY EXISTING FIELD CONDITIONS. DISCREPANCIES BETWEEN ACTUAL FIELDCONDITIONS AND CONTRACT DOCUMENTS SHALL BE BROUGHT TO THE ENGINEERS ATTENTION FOR ALTERNATIVE METHODS OFINSTALLATION PRIOR TO THE BIDDING OF THIS PROJECT.
19. UNLESS OTHERWISE NOTED ALL EXISTING MECHANICAL EQUIPMENT, PIPING, ETC, TO BE REMOVED SHALL BE DISPOSED OF BY THECONTRACTOR UNDER THIS CONTRACT. THE OWNER SHALL RETAIN THE RIGHT TO KEEP ANY REMOVED ITEMS.
20. ALL DOMESTIC COLD AND HOT WATER LINES IN THE AREA OF WORK WHICH ARE NO LONGER IN USE DUE TO THIS PROJECT SHALL BEREMOVED BACK TO THE MAINS AND CAPPED.
21. HOLES IN EXISTING WALL OR FLOORS SHALL BE PATCHED TO MATCH EXISTING WHERE PIPING, DUCTWORK, ETC. WERE REMOVEDOR ADDED DURING THIS PROJECT.
22. DAMAGE TO THE EXISTING FACILITY DURING THE CONSTRUCTION SHALL BE REPAIRED OR REPLACED BY THE CONTRACTOR AT NOCOST TO THE OWNER.
MECHANICAL ABBREVIATIONSA/C or AC AIR CONDITIONING IFGC INTERNATIONAL FUEL GAS CODE
AFF ABOVE FINISHED FLOOR IMC INTERNATIONAL MECHANICAL CODEAHU AIR HANDLING UNIT IPC INTERNATIONAL PLUMBING CODE
ASHRAE AMERICAN SOCIETY OF HEATING, REFRIGERATION,AND AIR CONDITIONING ENGINEERS KW KILOWATT
AV ACID VENT LINE KWH KILOWATT HOURAW ACID WASTE LINE
L LIQUID REFRIGERANT LINEBTU BRITISH THERMAL UNITS LAT LEAVING AIR TEMPERATURE
BTUH BTUS PER HOUR LAV LAVATORYLEED LEADERSHIP IN ENERGY & ENVIRONMENTAL DESIGN
CA COMBUSTION AIR LWT LEAVING WATER TEMPERATURECC COOLING COILCD CONDENSATE DRAIN LINE M MOTORIZED DAMPER
CDR CONDENSER WATER RETURN MAX MAXIMUMCDS CONDENSER WATER SUPPLY MCA MINIMUM CIRCUIT AMPSCFM AIR FLOW RATE (CUBIC FEET PER MINUTE) MIN MINIMUMCLG CEILING MOCP MAXIMUM OVERCURRENT PROTECTIONCW DOMESTIC COLD WATER MPG MEDIUM PRESSURE NATURAL GAS
CWR CHILLED WATER RETURNCWS CHILLED WATER SUPPLY NC NOISE CRITERIA
NFPA NATIONAL FIRE PROTECTION ASSOCIATIONDEG or ° DEGREE NTS NOT TO SCALEDIA or Ø DIAMETER
DB DRY BULB OD OVERFLOW DRAIN LINEDWR DOMESTIC HOT WATER RETURN OSA OUTSIDE AIR
EA EXHAUST AIR PD PRESSURE DROPEAT ENTERING AIR TEMPERATURE PH or Ø PHASEEER ENERGY EFFICIENCY RATIO PRV PRESSURE REDUCING VALVEESP EXTERNAL STATIC PRESSUREEWT ENTERING WATER TEMPERATURE RA RETURN AIR
RD ROOF DRAIN LINEF FIRE SPRINKLER LINE RPM REVOLUTIONS PER MINUTE
FCO FLOOR CLEANOUT RTU ROOFTOP UNITFD FIRE DAMPER
FLA FULL LOAD AMPS S SUCTION REFRIGERANT LINEFLR FLOOR SA SUPPLY AIRFPM FEET PER MINUTE SD STORM DRAIN LINEFS FLOW SWITCH SEER SEASONAL ENERGY EFFICIENCY RATIOFT FEET SFD COMBINATION SMOKE/FIRE DAMPER
SP STATIC PRESSUREG LOW PRESSURE NATURAL GAS SYM SYMBOL
GA GAUGEGCO GRADE CLEANOUT T & P TEMPERATURE AND PRESSUREGPM WATER FLOW RATE (GALLONS PER MINUTE) TEMP TEMPERATUREGWR GEOTHERMAL WATER RETURN TS TEMPERATURE SENSOR (DUCT OR PIPING)GWS GEOTHERMAL WATER SUPPLY TYP TYPICAL
HC HEATING COIL UPC UNIFORM PLUMBING CODEHP HORSE POWER U URINAL
HVAC HEATING, VENTILATING, AIR CONDITIONINGHW DOMESTIC HOT WATER VTR VENT THROUGH ROOF
HWR HEATING WATER RETURN V VOLTSHWS HEATING WATER SUPPLY
WB WET-BULBIBC INTERNATIONAL BUILDING CODE WC WATER CLOSET
IECC INTERNATIONAL ENERGY CONSERVATION CODE WCO WALL CLEANOUTIFC INTERNATIONAL FIRE CODE WH WATER HEATER
NOTE: THIS IS A STANDARD LIST OF COMMONLY USED MECHANICAL ABBREVIATIONS. SOME OF THE ABBREVIATIONS SHOWN ABOVEMAY NOT BE USED IN THIS DRAWING PACKAGE.
MECHANICAL GENERAL NOTES
MECHANICAL AND PLUMBING DRAWINGS LEGENDFLEXIBLE DUCTWORK THREE WAY CONTROL VALVE
DUCTWORK TWO WAY CONTROL VALVE
DUCTWORK BREAK PRESSURE REDUCING VALVE
DUCTWORK OR PIPING RISE GATE VALVE
CONCENTRIC SQUARE TO ROUNDTRANSITION REDUCER
MOTORIZED DAMPER GLOBE VALVE
MANUAL VOLUME DAMPER BALL VALVE
SPIN-IN FITTING W/ AIR EXTRACTOR ANDHAND DAMPER BUTTERFLY VALVE
HIGH EFFICIENCY FITTING W/ HANDDAMPER BALANCE VALVE
SWITCH CHECK VALVE
THERMOSTAT FLOOR CLEANOUT
HUMIDISTAT WALL CLEANOUT
TEMPERATURE SENSOR GRADE CLEANOUT
CARBON DIOXIDE SENSOR WATER HAMMER ARRESTOR
CARBON MONOXIDE SENSOR FLOOR DRAIN
NITROUS OXIDE SENSOR FLOOR SINK
DUCT SMOKE DETECTOR GAS PRESSURE REGULATOR W/ GASCOCK
1. SIDEWALK AREA SHOWN SHADED IS TO BE PROVIDED WITH A SNOW MELTSYSTEM. PROVIDE SLAB INSULATION BELOW TUBING PER RADIANT TUBINGANCHORING DETAIL ON SHEET M4.2.
2. NEW SHOP ADDITION.
3. THIS CONCRETE SLAB SHOWN SHADED IS TO BE PROVIDED WITH A SNOWMELT SYSTEM. PROVIDE SLAB INSULATION BELOW TUBING PER RADIANTTUBING ANCHORING DETAIL ON SHEET M4.2.
1. EVAPORATIVE COOLER LOCATED HIGH ON EXTERIOR WALL.
2. UPBLAST EXHAUST FAN LOCATED ON THE ROOF.
3. EXTERIOR WALL LOUVER WITH MOTORIZED DAMPER LOCATED HIGH ONWALL. SEE ARCHITECT'S EXTERIOR ELEVATIONS FOR EXACT LOCATION OFWALL LOUVER. DAMPER SHALL BE INTERLOCKED WITH EVAPORATIVECOOLERS AND CARBON MONOXIDE WALL SENSOR.
4. INLINE CABINET FAN WITH HANGING VIBRATION ISOLATORS AND FLEXIBLECONNECTION AT INLET AND OUTLET. ROUTE 10"Ø EXHAUST DUCT TO ANEXTERIOR WALL CAP.
5. HONEYWELL E3POINT DUAL-GAS DETECTOR. PROVIDE HONEYWELL MODELE3SARHSCO + E3SRMNO2. SENSOR SHALL BE SURFACE-MOUNT,DUAL-MODE, 120 VOLT.
6. VEHICLE EXHAUST WALL PORT THAT IS COMPATIBLE WITH PORTABLEVEHICLE EXHAUST SYSTEM. SEE ARCHITECTURAL FOR SPECIFICATIONS.
7. EXTERIOR WALL LOUVER. BOTTOM OF LOUVER SHALL BE 9'-0" TO 10'-0"ABOVE THE FINISHED FLOOR. SEE ARCHITECT'S EXTERIOR ELEVATIONS FOREXACT LOCATION.
8. PROVIDE EXPANDED METAL GRATE WITH TAMPER PROOF SCREWS ON 5'-4"X 4'-8" DUCT CONNECTED WITH LOUVER (L-2).
9. WALL SWITCH CONTROLS FOR EVAPORATIVE COOLER. REFERENCEELECTRICAL PLANS.
10. CEILING CABINET FAN WITH HANGING VIBRATION ISOLATORS AND FLEXIBLECONNECTION AT OUTLET. ROUTE 12-INCH DIAMETER EXHAUST DUCT UPTHRU ROOF AND TERMINATE WITH ROOF CAP. FAN SHALL BE CONTROLLEDBY A HEAT RISE THERMOSTAT.
11. EVAPORATIVE COOLER (EC-1) MOUNTED ON WALL SUPPORT ABOVEMECHANICAL ROOM ROOF. REFERENCE ARCHITECTURAL PLANS FORCONSTRUCTION OF WALL SUPPORT. SEE EVAPORATIVE COOLER PIPINGDETAIL ON SHEET P3.1.
1. INSTALL WATER HEATER PER SCHEMATICS ON SHEET M5.0.
2. EXISTING SNOW MELT WATER HEATER IS TO BE RELOCATED. REMOVEALL ASSOCIATED PIPING WITH THIS WATER HEATER TO BE RELOCATED.CAP GAS LINE OFF AT THE MAIN. SEE SHEET M4.1 FOR SCHEMATICS ONINTEGRATION TO NEW SNOW MELT SYSTEM AT NEW LOCATION INJANITOR'S ROOM.
3. EXISTING WATER HEATER TO REMAIN.
4. REMOVE EXISTING MANIFOLDS AND ALL ASSOCIATED PIPING BACK TOSNOW MELT PUMP TO BE REMOVED.
5. INSTALL FLOOR SINK. CONNECT DRAIN TO WASTE LINE BELOW. ROUTENEW VENT TO CEILING ABOVE. CONNECT TO EXISTING VENT PIPE.CONTRACTOR TO FIELD VERIFY PIPING REQUIREMENTS.
6. TERMINATE OUTSIDE AIR DUCT AT MANUFACTURERS WALL CAP ATAPPROXIMATELY 15' AFF.
7. TERMINATE FLUE DUCT AT MANUFACTURERS WALL CAP ATAPPROXIMATELY 15' AFF.
8. INSTALL GLYCOL MAKE-UP TANK. SEE DETAIL ON SHEET M4.2 FOR MOREINFORMATION.
9. EXISTING OUTSIDE AIR INTAKE LOUVER.
10. INSTALL NEW GAS REGULATOR.
11. NEW LOCATION FOR EXISTING WATER HEATER (WH-1).
12. REMOVE EXISTING SNOW MELT PUMP. REMOVE PIPING TO EXISITINGMANIFOLDS.
13. CONNECT TO NEW WATER HEATERS PER SCHEMATICS ON SHEET M5.0.
14. INSTALL NEW MANIFOLD FOR NEW SNOW MELT SYSTEM ABOVEJANITOR'S SINK.
15. NEW SNOW MELT CONTROL PANEL.
16. NEW GAS PIPING ROUTED BELOW GRADE.
SCALE: 1/4" = 1'
South Enlarged Snow Melt & Domestic Hot Water Floor PlanM1.62
1/2" (E)
ADD ALTERNATE
ADD ALTERNATE
DDDDDDDDDDDDDDDDD
5-9-16
NOTE:ALL DUCTWORK TRANSITIONS SHALL BE CONSTRUCTED AND INSTALLED TO SMACNA, SPECIFICATIONS AND THE ABOVE NOTEDSTANDARDS. ANY DEVIATIONS SHALL BE COORDINATED WITH THE ENGINEER.
O = 15° MAXIMUM20% MAX AREA REDUCTION
O = 30° MAXIMUM
X
R=1.0X
X X
X
X
O = 45° MAXIMUM
R=6" MIN.
1/4
O = 15° MAXIMUM
X
O
X
X
R=1.0X
X
X
1/21/4
R=6" MIN.
X X
O
O
R.A.
90° TURNING VANES
S.A.
X
Y
.25Y, 4" MIN.
X
Y
R=1.5X
X
Y X
X+Y
YY
O
X
O
X
Z
SCALE: NOT TO SCALERECTANGULAR DUCT FITTING DETAILS1
DUCT TAKE-OFF RADIUS WYESQUARE TEE W/TURNING VANES
SQUARE TEE W/DUCT TAKE-OFFS
X
X
R=1.5X
X
90° TURNING VANES
X
X
R=1.5X
X
X
X
R=1.5X
XX
Y
Y
Z
X
1.5X
Z
X
Y
X
6"
Y+2
Y
Y=3"-8", Z=3"Y=17"-24", Z=9"
XZ
Y
X
Y = 2X; Z = SEE PLANS
Y
Z
XX
Y
X
X
Y
Z
X
Z = X - Y (4" MIN.)
X
Y=9"-16", Z=6"Y=25" UP, Z=12"
SCALE: NOT TO SCALEROUND DUCT FITTING DETAILS2
NOTE:ALL DUCTWORK TRANSITIONS SHALL BE CONSTRUCTED AND INSTALLED TO SMACNA, SPECIFICATIONS, AND THE ABOVE NOTEDSTANDARDS. ANY DEVIATIONS SHALL BE COORDINATED WITH THE ENGINEER.
WYE FITTINGOFFSETECCENTRICTRANSITION
CONCENTRICTRANSITION
90° TEE FITTING CONICAL FITTING 90° TEE W/OVALTO ROUND TAP 45° LATERAL TAP
RADIUS ELBOW 90° GORED ELBOW5 GORE
MITERED ELBOW W/TURNING VANES
45° GORED ELBOW3 GORE
18" GAGE MINIMUMBLADE 6" TO 9" WIDE.
NOTES:
1. FOR TAKE-OFFS LARGER THAN 12" DIAMETER, USE A FACTORY MANUFACTURED DAMPER. LOUVERS& DAMPERS, INC. MODEL CD-600 WITH A LOCKING HAND QUADRANT OR EQUAL.
2. ROD CONTINUOUS ON 2" W.G. CLASS AND ON ALL DAMPERS OVER 12" DIAMETER.
3. BLADE 22 GAGE MIN., BUT NOT LESS THAN TWO GAGES MORE THAN THE DUCT GAGE.
4. PROVIDE REMOTE CEILING OPERATOR WHERE DAMPER IS INACCESSIBLE.
5. FOR DUCTS OVER 12" HIGH USE MULTIPLE BLADE DAMPERS (SEE FIG. C).
6. ALTERNATE MANUFACTURERS: AMERICAN WARMING, SAFE-AIR/DOWCO, J & J, LOUVERS &DAMPERS, RUSKIN, NAILOR, ARROW UNITED, POTTORFF & CESCO.
SCALE: NOT TO SCALEBALANCE DAMPER DETAIL3
VOLUME DAMPER(SEE NOTE 1)
WING NUT
DAMPER ARM(SEE NOTE 4)
DAMPER BLADE(SEE NOTE 3)
ROUND DUCTROD (SEE NOTE 2)
FIG. A
DUCT
1/2" QUADRANT DUCT
1/2" ROD
18 GA. BLADE MIN.
1/8" CLEARANCEALL AROUND
19" TO 48"
FIG. D
FIG. B
UP TO 18"
1/8" CLEARANCEALL AROUND
22 GA. BLADE
3/8" PIN
HEMMED EDGEDUCT3/8" QUADRANT
FIG. CELEVATION, TWO
BLADE ARRANGEMENT
AIR
FLOWX
45°
Y
STAND OFF
SCALE: NOT TO SCALESPIRAL DUCT HIGH EFFICIENCY TAKE-OFF DETAIL4
LOCKING QUADRANT HANDLEOR REMOTE CEILINGOPERATOR WHERE DAMPERIS INACCESSIBLE
RIGID SPIRAL DUCT(SEE PLAN FOR SIZE)
BALANCE DAMPER(SEE NOTE 2)
HIGH EFFICIENCYDUCT TAKE-OFF(SEE NOTES 1 & 3)
RIGID SPIRAL DUCT(SEE PLAN FOR SIZE)
NOTES:
1. TAKE-OFFS SHOULD NOT BE INSTALLED CLOSER THANTWO WIDTHS TO ELBOWS OR INTERSECTIONS.
NOTE:PROVIDE AUTOMATIC AIR VENTS AT WELLWATER SYSTEM PIPED TO THE GLYCOL TANK.PROVIDE MANUAL AIR VENTS AT ALL OTHERHIGH SPOTS OUTSIDE THE MECHANICALROOM
NOTE:PROVIDE 4" THICK HOUSKEEPING PAD FORALL BASE MOUNTED EQUIPMENT. SECUREEQUIPMENT TO THE HOUSEKEEPING PAD.
NOTE:PROVIDE GLYCOL FEED TANK AS REQUIREDFOR MAKE-UP TO THE GLYCOL PIPINGSYSTEMS (AXIOM OR EQUAL). ALL AUTO AIRVENTS SHALL BE DRAINED BACK TO THETANK FOR RECOVERY PURPOSES.
HWS
HWR
(13.5.0 GPM)
DRAIN VALVE(TYPICAL)
STRAINER (TYPICAL)
NO NO
HWS
HWR
HWS
HWR
(13.5 GPM)
STRAINER
NO NO
HWSHWRHWR
HWS
1-1/4"1-1/4"
2"
1-1/4" 2"
HWS
HWR
SMHS
SMHR
3/4" GLYCOL FILL LINETO GLYCOL TANK
NO
NO3/4"
NO
1ET
INLINE AIR SEPARATOR2"
HIGH CAPACITYAIR VENT
SM
HS
SM
HR
ROUTE TO RADIANT FLOORSYSTEM MANIFOLDS
NO
NO
2"
1RFP
4WH
3WH
PROP
ANE
G
2-1/2"
B&G MODEL HFT-90EXPANSION TANK
T & PRELIEF VALVE
T & PRELIEF VALVE
1 1/2"
HWS
HWR
HWS
HWR
(13.5 GPM)
STRAINER
NO NO
1-1/4"
5WH
T & PRELIEF VALVE
1-1/4"
ROUTE TO SNOW MELTSYSTEM MANIFOLDS
NO
NO
2"
3SMP
SCALE: NOT TO SCALESNOW MELT / RADIANT FLOOR PIPING SCHEMATIC3
SCALE: NOT TO SCALESNOW MELT CONTROL SCHEMATIC1
HWS
HWR
(12.75 GPM)
T & PRELIEF VALVE
DRAIN VALVE(TYPICAL)
STRAINER (TYPICAL)
NO NO
HWS
HWR
HWS
HWR
(12.75 GPM)
STRAINER
NO NO
HWSHWRHWR
HWS
1-1/4"1-1/4"
1-1/4"
1-1/4" 2"
HWS
HWR
SM
HS
SM
HR
3/4" GLYCOL FILL LINETO GLYCOL TANK
NO
NO3/4"
NO
1ET
INLINE AIR SEPARATOR2"
HIGH CAPACITYAIR VENT
SM
HS
SM
HR
ROUTE TO SNOW MELTSYSTEM MANIFOLDS
NO
NO
2"
1SMP
2WH
1WH
PROP
ANE
G
B&G MODEL HFT-90EXPANSION TANK
2"
T & PRELIEF VALVE
1 1/4"
SCALE: NOT TO SCALESNOW MELT PIPING SCHEMATIC4
ADD ALTERNATE
ADD ALTERNATE
ROUTE TO SNOW MELTSYSTEM MANIFOLDS
NO
NO
2"
2SMP
(E)
1"1"1"
1 1/4"
1"
1"
SNOW MELT CONTRACTOR SHALL COORDINATEWITH ELECTRICAL CONTRACTOR FOR FINALLOCATION OF SENSORS.
NOTE:
(TYPICAL OF 2)
SNOW MELT PUMP (SMP-1)
TEKMARSNOW MELT
CONTROLLER
SNOW AND ICE SENSOR
TEKMAR OUTSIDE AIRTEMPERATURESENSOR
SNOW MELT CONTRACTOR SHALL COORDINATEWITH ELECTRICAL CONTRACTOR FOR FINALLOCATION OF SENSORS.
CONTRACTOR SHALL SUBMIT A METAL COVER DESIGN TO THE OWNER FOR FINAL APPROVAL.
ALL ABOVE FLOOR SUPPLY AND RETURN PIPING SHALL BE INSULATED TYPE "L" HARD DRAWNCOPPER. ALL UNDER FLOOR PIPING SHALL BE hePEX PIPING AS NOTED ON THE HEADERSCHEDULE. CONTRACTOR SHALL COORDINATE WITH THE GENERAL CONTRACTOR THEEXACT LOCATION OF THE TRANSITION BETWEEN THE COPPER AND hePEX PIPING. ALL PIPINGINSTALLATIONS MUST BE IN ACCORDANCE TO MANUFACTURER'S WARRANTYREQUIREMENTS.
SUPPLY HEADER
(UNISTRUT ORFEE & MASON)
1" CHANNELSET CIRCUIT SETTER TO GPMINDICATED ON SCHEDULE
RETURN HEADER
RADIANT FLOOR RETURN FLOW BALANCINGCAPS (EQUALIZE FLOW THRU ALL LOOPS)
RETU
RN
SUPP
LY
PROVIDE AN 18 GAUGE STAINLESS STEEL OR ALLUMINUMCOVER OVER HEADERS IN PEN AREAS. COVER SHALLINCLUDE ACCESS DOOR WITH A CONTINUOUS HINGEFOR ACCESS TO ALL CONTROL VALVES.
BALL VALVE (TYPICAL)
NOTES:
SLOPE TOP OF COVER FORWATER DRAIN OFF.
1.
2.
EXTEND HEADER AND PIPECOVER UP TO THE CEILING.SEAL COVER TO CEILING, WALLAND FLOOR WATER TIGHT.
SEAL COVER TO WALL AND FLOORWATER TLIGHT.
TEMPERATURE GAUGE
SCALE: NOT TO SCALE (TYPICAL AT ALL RADIANT FLOOR HEADERS)HEADER PIPING AND SUPPORT DETAIL2
SUPPLY
RETURN
ALL SNOW MELT AND RADIANT FLOOR TUBING MUST BE INSTALLED IN ACOUNTER FLOW PATTERN. COUNTER-FLOW RUNS THE WARMEST WATERIN THE LOOP NEXT TO THE COOLEST. THIS IS CRITICAL TO ENSURE THATALL PARTS OF THE SNOW MELT AREA RECEIVE ADEQUATE SUPPLYTEMPERATURE.
NOTE:
SCALE: NOT TO SCALECOUNTER-FLOW PATTERN1
SCALE: NOT TO SCALERADIANT TUBING ANCHORING DETAIL3
TUBING MOUNTING
CONCRETE SLAB
RADIANT TUBING
FOAM STAPLES
BASE MATERIAL
RIGID R-5 SLABINSULATION
ANCHOR RADIANT TUBING TO RIGID UNDER SLAB R-5INSULATION USING FOAM STAPLES.
ROUTE HOSE UNDER EXPANSION JOINTS,CONSTRUCTION JOINTS, AND CONTROL JOINTS. (SEESTRUCTURAL)
CONCRETE SLAB(SEE STRUCTURAL)
CONCRETE REINFORCING(SEE STRUCTURAL)
SCALE: NOT TO SCALEEXPANSION JOINT PIPING DETAIL4
NOTES:
1. INITIAL SYSTEM PRESSURE SHALL BE SET AS INDICATED IN THE EXPANSION TANKSCHEDULE. TANK SHALL BE FILLED FULL WITH A SOLUTION OF 35% DOWFROSTPROPYLENE GLYCOL AND 65% CLEAN WATER.
2. INSTALL ALL VALVES IN ACCESSIBLE LOCATIONS FOR MAINTENANCE PURPOSES.
LOW LEVEL ANDALARM CONTROLBOX
HOSE ASSEMBLYWITH STRAINER
VALVE
CONNECT 1/2" MAKE-UP WATER TOCHILLED WATER SYSTEM'S ORHEATING WATER SYSTEM'S AIRSEPARATOR OR STORAGE TANK
LID
SOLUTION CONTAINER
PUMP W/ BUILT-INPRV AND SHUT-OFFVALVE(TYP.)
4" THICK CONCRETE HOUSEKEEPINGPAD SECURE TO CONCRETE FLOORW/ FOUNDATION BOLTS
SCALE: NOT TO SCALESINGLE PUMP GLYCOL MAKE-UP PACKAGE DETAIL5
2. PROVIDE WITH FACTORY INSTALLED MOTOR AND PUMP, FLOAT OPERATED SOLENOID, FILL & DRAIN KIT WITH 120 V SOLENOID VALVES (2 WAY DRAIN-N.O., 3 WAY FILL & DRAIN VALVE, AUTOMATIC BLEED OFF KIT, AND PRESSURE REG. VALVE - NOT TOEXCEED 50 PSI). PROVIDE (1) SEPARATE WALL SWITCH WITH PILOT LIGHT FOR OPERATION OF FAN, (1) SEPARATE WALL SWITCH WITH PILOT LIGHT FOR PUMP CONTROL, AND (1) SEPARATE WALL SWITCH WITH PILOT LIGHT FOR CONTROL OF FILL ANDDRAIN OF EVAPORATIVE COOLER (LABEL ALL SWITCHES). SWITCH CONTROL PANEL AND WIRING BY ELECTRICAL CONTRACTOR, SEE ELECTRICAL DRAWINGS.
EVAPORATIVE COOLER SCHEDULE
SYMBOL AREA SERVED TYPE COOLINGCAPACITY
SUPPLY FAN OPERATING CONDITIONS (°F) (2) PUMPSOPERATING
EF-1 SHOP AND TOILET ROOM INLINE CABINET 350 .5 1400 DIRECT 99.0 W 120/1Ø 3.0 30 COOK MODEL GN-622 1 , 2 , 8
EF-2 OXY WELDING BOOTHS WALL MOUNTED FAN 1875 1.2 1524 BELT .75 HP 208/1Ø 14.4 75 COOK MODEL 165 ACWB-HP 1 , 3 , 6 , 9
EF-3 ARC WELDING BOOTHS WALL MOUNTED FAN 4900 1.2 1151 BELT 2 HP 208/1Ø 19.2 170 COOK MODEL 210 ACWB 1 , 3 , 6 , 9
EF-4 SHOP AND PLASMA TABLE WALL MOUNTED FAN 1425 .75 1146 BELT .334 HP 208/1Ø 11.4 70 COOK MODEL 150 ACWB 1 , 3 , 7 , 9
EF-5 MECHANICAL ROOM CEILING CABINET 440 .5 1500 DIRECT 133.0 W 120/1Ø 3.5 30 COOK MODEL GC-642 1 , 4 , 5
REMARKS:
1. APPROVED ALTERNATE MANUFACTURERS: GREENHECK, PENNBARRY, ACME, TWIN CITY FAN COMPANY, SOLER & PALAU, AND BARRY BLOWER.
2. PROVIDE UNIT WITH MANUFACTURER'S MANUFACTURER'S WALL CAP EQUAL TO COOK MODEL WCG (W/ INTEGRAL BIRDSCREEN), BACKDRAFT DAMPER, INLET AND OUTLET FLEX DUCT CONNECTIONS, STANDARD PLUG DISCONNECT, PRE-WIRED FAN SPEED CONTROLLER,THERMAL OVERLOAD PROTECTION, AND HANGING VIBRATION ISOLATORS.
3. PROVIDE UNIT WITH MANUFACTURER'S BACKDRAFT DAMPER, THERMAL OVERLOAD PROTECTION (120 VOLT ONLY), PRE-WIRED NEMA 3R ELECTRICAL DISCONNECT SWITCH, AND INTEGRAL BIRD SCREEN.
4. PROVIDE UNIT WITH MANUFACTURER'S ALUMINUM ROOF CAP (FLAT ROOF) EQUAL TO COOK MODEL PR (W/ INTEGRAL BIRD SCREEN AND ROOF CURB), BACKDRAFT DAMPER, OUTLET FLEX DUCT CONNECTION, STANDARD PLUG DISCONNECT, PRE-WIRED FAN SPEEDCONTROLLER, THERMAL OVERLOAD PROTECTION, HANGING VIBRATION ISOLATORS, AND WHITE ALUMINUM GRILLE.
5. CONTROL FAN WITH HEAT RISE THERMOSTAT.
6. CONTROL FAN WITH SEPARATE WALL SWITCH.
7. CONTROL FAN WITH SEPARATE WALL SWITCH AND WALL SENSOR.
8. CONTROL FAN WITH A TIME CLOCK. FAN SHALL RUN CONTINUOUSLY DURING OCCUPIED HOURS.
1. SIZES BASED ON TITUS MODEL 50F, ALUMINUM EGGCRATE RETURN GRILLE, 1/2" x 1/2" x 1" SPACING (SINGLECORE). PROVIDE SQUARE TO ROUND TRANSITION (WHERE ROUND RUN-OUT INDICATED). APPROVEDALTERNATE MANUFACTURERS INCLUDE , ANEMOSTAT, CARNES, PRICE, NAILOR, METAL-AIRE, TUTTLE & BAILEY,KRUEGER, J&J REGISTER, AND UNITED ENERTECH.
2. SIZES BASED ON A MAXIMUM NC LEVEL OF 25.
3. ALL GRILLES LOCATED IN HARD CEILING AREAS SHALL HAVE BORDER #1, UNLESS OTHERWISE INDICATED.REFER TO ARCHITECTURAL PLANS FOR LOCATIONS OF VARIOUS CEILING TYPES. SHEET METAL DUCTWORKVISIBLE BEHIND GRILLE SHALL BE PAINTED FLAT BLACK.
4. ALL OF THE GRILLES SHOWN IN THIS SCHEDULE MAY NOT BE USED. REFERENCE THE HVAC PLAN FOR GRILLECALL-OUTS AND THE QUANTITY OF EACH SIZE REQUIRED.
5. WHENEVER THERE IS A DISCREPANCY BETWEEN THE RUNOUT DUCT SIZE SHOWN ON THE PLANS AND THATSHOWN IN THE SCHEDULE, ALWAYS USE THE LARGER OF THE TWO DUCT SIZES.
6. WHITE FINISH.
22X22R-3
10"ØR-2
8"ØR-1
MANIFOLD #
SNOW MELT CIRCUITS ARE TO BE EQUAL LENGTHS OFF EACH MANIFOLD. PROVIDE A 3/4" BALL VALVE FOR EACH OF THE LOOPS. PROVIDE A BALANCE VALVE FOR EACH RETURN MANIFOLD.
WATER SOLUTION SHALL BE 50% PROPYLENE GLYCOL/50% WATER.
27.1 30 1IN-LINE PUMP GRUNDFOS MAGNA 40-120SNOW MELT HEAT
ZONE(2, 3)1SMP
-- 120/1442 -- VARIABLE
25.5 30 1IN-LINE PUMP GRUNDFOS MAGNA 40-120SNOW MELT HEAT
ZONE (1, 4)2SMP
-- 120/1442 -- VARIABLE
30
30
SNOW MELT 5
SNOW MELT 6
SNOW MELT 5
SNOW MELT 6
1507
200
123.1
123.1
5
4
hePEX 1"
hePEX 1"
442
97
9
9
130
130
30
30
37
37
14.4
1.9
9.1
0.1
21
21
REMARKS:
1. APPROVED ALTERNATE MANUFACTURERS: HASTINGS, TRANE, REZNOR, AND STERLING.
2. PROVIDE UNIT WITH MANUAL SUMMER/WINTER SWITCH, THERMOSTAT AND RELAY KIT, 65° DOWNTURN NOZZLE WITH HORIZONTAL LOUVERS, THROUGH THE ROOF CONCENTRIC VENT KIT AND 4-POINT SUSPENSION KIT.
25.5 30 1IN-LINE PUMP GRUNDFOS MAGNA 40-120SNOW MELT HEAT
ZONE (5, 6)3SMP
-- 120/1442 -- VARIABLE 30
25.5 30 1IN-LINE PUMP GRUNDFOS MAGNA 40-120RADIANT FLOOR HEAT
ZONE 11RFP
-- 120/1442 -- VARIABLE 30
2
2
2
SYMBOL FIXTURE DESCRIPTION
CONNECTION SIZE
MANUFACTURER / MODEL NUMBER / DESCRIPTION / ADDITIONAL COMMENTSWASTE VENT TRAP CW HW
WH-1EXISTING WATER HEATER(NOMINAL 100 GALLON)(PROPANE)
-- -- -- SEEPLANS
SEEPLANS
AO SMITH MODEL BTH-199, 199 MBH INPUT, 110V/1Ø, 28" DIAMETER, 76" TALL WITH SIDECONNECTIONS.
WH-2WATER HEATER(NOMINAL 100 GALLON)(PROPANE)
-- -- -- SEEPLANS
SEEPLANS
AO SMITH MODEL BTH-250, 250 MBH INPUT, 110V/1Ø, 28" DIAMETER, 76" TALL WITH SIDECONNECTIONS. PROVIDE WITH PVC CONCENTRIC INTAKE/VENT KIT AND SEISMIC STRAP.
WH-3WATER HEATER(NOMINAL 130 GALLON)(PROPANE)
-- -- -- SEEPLANS
SEEPLANS
AO SMITH MODEL BTH-300, 300 MBH INPUT, 110V/1Ø, 33" DIAMETER, 76" TALL WITH SIDECONNECTIONS. PROVIDE WITH PVC CONCENTRIC INTAKE/VENT KIT AND SEISMIC STRAP.
WH-4WATER HEATER(NOMINAL 130 GALLON)(PROPANE)
-- -- -- SEEPLANS
SEEPLANS
AO SMITH MODEL BTH-300, 300 MBH INPUT, 110V/1Ø, 33" DIAMETER, 76" TALL WITH SIDECONNECTIONS. PROVIDE WITH PVC CONCENTRIC INTAKE/VENT KIT AND SEISMIC STRAP.
WH-5WATER HEATER(NOMINAL 130 GALLON)(PROPANE)
-- -- -- SEEPLANS
SEEPLANS
AO SMITH MODEL BTH-300, 300 MBH INPUT, 110V/1Ø, 33" DIAMETER, 76" TALL WITH SIDECONNECTIONS. PROVIDE WITH PVC CONCENTRIC INTAKE/VENT KIT AND SEISMIC STRAP.
NOTES:1. ALL EXPOSED HW PIPING, CW PIPING, AND DRAIN LINES BENEATH ALL LAVATORIES AND ALL ADA COMPLIANT SINKS MUST BE INSULATED TO PREVENT INJURY. REFER TO ARCHITECTURAL PLANS.
INSULATE WITH MOLDED CLOSED CELL VINYL INSULATION - TRUEBRO, PLUMBEREX, OR EQUAL.
2. SEE SPECIFICATIONS FOR ALTERNATE APPROVED MANUFACTURERS.
WATER HEATER SCHEDULE
ADD
ALTE
RNAT
E
ADD
ALTE
RNAT
EAD
DAL
TERN
ATE
REMARKS:
1. RADIANT FLOOR CIRCUITS TO BE EQUAL LENGTHS OFF EACH MANIFOLD WITH A 300 FT MAXIMUM TUBE LENGTH. PROVIDE A 1/2" BALL VALVE FOR EACH OF THE LOOPS. RADIANT FLOOR MANIFOLD DESIGN BASED ON UPONOR STAINLESS STEEL MANIFOLDWITH ISOLATION VALVES AND VISUAL FLOW GUAGES. ALTERNATES SHALL BE EQUAL IN QUALITY AND PERFORMANCE.
2. PROVIDE A 50% PROPYLENE GLYCOL/50% WATER SOLUTION.
3. TUBING RATED FOR 180° F AT 100 PSI SERVICE.
4. SEE HYDRONIC PIPING DIAGRAM ON SHEET M41.
RADIANT FLOOR MANIFOLD SCHEDULEZONE # AREA (ft2) CONSTRUCTION TYPE
1. 2-INCH DOMESTIC WATER SERVICE. SEE SITE UTILITY PLANS FORCONTINUATION OF THIS LINE.
2. DOMESTIC COLD WATER ROUTED HIGH AT ROOF STRUCTURE.
3. MAIN DOMESTIC WATER SHUT-OFF VALVE FOR SHOP BUILDING.
4. REDUCED PRESSURE BACKFLOW PREVENTER (RPBP-1). INSTALL PERMANUFACTURER'S INSTALLATION INSTRUCTIONS. ACCESS AND CLEARANCESHALL BE PROVIDED FOR THE REQUIRED TESTING, MAINTENANCE, ANDREPAIR. PROVIDE A MINIMUM CLEARANCE OF 1-FOOT BETWEEN LOWESTPORTION OF THE ASSEMBLY AND FLOOR. RUN A DRAIN LINE FROM RPBP-1TO UTILITY SINK (US-1).
5. ELECTRIC WATER HEATER (WH-1) MOUNTED ON TOILET ROOM CEILINGSTRUCTURE. PROVIDE A DRAIN PAN AND PIPE DRAIN TO UTILITY SINK (US-1).SEE WATER HEATER DETAIL ON SHEET P3.0.
BRONZE CLEANOUT PLUG WITH COUNTERSUNK HEAD. SEE THE PLUMBING FIXTURESCHEDULE FOR MANUFACTURER AND MODEL.
45° ELBOW
45° WYE
SAME SIZE AND MATERIALAS THE SEWER PIPING
CAP AT TERMINUS
SANITARY SEWER LINE (PVC,ASTM D3033 OR D3034, SDR 35,WITH ELASTOMERIC GASKETS)
FINISH PAVEMENT
SCREW CAP/PLUG
45° ELBOW
45° WYE
ROUND FLANGED HOUSING WITH HEAVY DUTYCAST IRON COVER. COVER TO BE INSCRIBED" S A N " . S E E T H E P L U M B I N G F I X T U R ESCHEDULE FOR MANUFACTURER AND MODEL.
SAME SIZE AND MATERIALAS THE SEWER PIPING
CAP AT TERMINUS
SANITARY SEWER LINE(PVC, ASTM D3033 ORD 3 0 3 4 , S D R 3 5 , W I T HELASTOMERIC GASKETS)
BALANCE OF PIPING, SEESPECIFICATIONS FOR PIPEMATERIAL.
NOTE:CLEANOUTS SHALL BE PROVIDED AT EACH HORIZONTAL DRAINAGE PIPE AT ITS UPPERTERMINAL, AND EACH RUN OF PIPING WHICH IS MORE THAN 100 FEET, AND SHALL BE PROVIDEDFOR EACH 100 FEET DEVELOPED LENGTH, OR FRACTION THEREOF OF SUCH PIPING. ANADDITIONAL CLEANOUT SHALL BE PROVIDED FOR EACH AGGREGATE HORIZONTAL CHANGE OFDIRECTION EXCEEDING ONE HUNDRED THIRTY-FIVE DEGREES, PER APPLICABLE PLUMBINGCODE. THIS SHALL BE PROVIDED REGARDLESS OF WHAT IS SHOWN ON THE DRAWINGS.
CLEANOUT AND ACCESS COVER.TOP OF COVER TO BE FLUSHWITH TOP OF FLOOR.
NOT TO SCALEFLOOR CLEANOUT (FCO) DETAIL3
NOT TO SCALESINK/LAVATORY TAILPIECE & TRAP DETAIL5
NOTES:A. INTERIOR EXPOSED PIPE, VALVES AND FIXTURE TRIM, INCLUDING
TRIM BEHIND CASEWORK DOORS SHALL BE CHROME PLATED.
B. ALL PIPING PENETRATIONS THROUGH FINISHED WALLS SHALL BEPROVIDED WITH CHROME ESCUTCHEONS.
C. ALL SINK TRAPS SHALL BE PROVIDED WITH A CLEANOUT PLUG INTHE BOTTOM OF THE TRAP.
D. ALL PLUMBING FIXTURES SHALL BE CAULKED AND SEALED TOSURROUNDING SURFACES.
SEE PLUMBING FIXTURESCHEDULE FOR BOWL &FAUCET SPECIFICATIONS
K-4302
HIGHCRESTC_TOILETS
VITREOUS CHINA
FLUSH VALVE
1-1/2"x12" 17 GA. FLUSH VALVE PRIMER TUBEWITH 1/2" COMPRESSION FITTING.
WATER CLOSET
FLOOR
P-TRAP1/2" TRAPPRIMER LINE
1/2" TRAP PRIMER SUPPLY
DOMESTIC WATER LINE
TRAP PRIMER
DISTRIBUTION UNIT
1/2" TRAP PRIMER LINE
FLOOR DRAIN
SLEEVE THRU SLAB
FLOOR DRAIN
FLOOR
FLUSH VALVE PRIMER NOTES:
1. THE FLUSH VALVE PRIMER IS DESIGNED TO PRIME ONE FLOORDRAIN TRAP AT A DISTANCE NOT TO EXCEED 20 FEET FROM POINTOF INSTALLATION.
2. THE FLUSH VALVE PRIMER SHALL BE INSTALLED WITH A VACUUMBREAKER.
3. FLUSH VALVE PRIMER IS INTENDED FOR USE WITH WATER CLOSETSCONSUMING 3.5 TO 1.0 GAL/FLUSH.
4. TRAP PRIMER SHALL BE PRECISION PLUMBING PRODUCTS MODELFVP-1VB WITH VACUUM BREAKER.APPROVED ALTERNATES: MIFAB, SIOUX CHIEF, AND ZURN.
PRESSURE ACTIVATED PRIMER NOTES:
1. THE PRIMING VALVE MUST BE INSTALLED ON A FRESH COLD WATER LINE OF1/2" TO 1-1/2" DIAMETER.
2. DISTRIBUTION UNIT MUST BE INSTALLED LEVEL WITH AN ACCESS DOOR FORPERIODIC INSPECTION.
3. DO NOT SUBJECT TRAP PRIMER VALVE TO ROUGH-IN PRESSURE TEST.
4. DISTANCE FROM DISTRIBUTION UNIT TO FLOOR MUST BE 12" FOR EVERY 20'HORIZONTALLY.
5. TRAP PRIMER SHALL BE PRECISION PLUMBING PRODUCTS MODEL CPO-500WITH DU DISTRIBUTION UNIT IF REQUIRED. APPROVED ALTERNATES: MIFAB,SIOUX CHIEF, AND ZURN.
1/2" CHROME PLATED TRAP PRIMER LINE. OFF
ON
BALL TYPE SHUT-OFF VALVE
POSITION BEVELED END FACING UP
NOT TO SCALETRAP PRIMER CONNECTION DETAIL6
BALL VALVE
THERMOMETER
3/4" COLD WATER3/4" HOT WATER
WALL
R
WH-6
WATTS RESTRAINT
T & P RELIEF VALVE
NOT TO SCALEWATER HEATER PIPING DETAIL4
NON-CORROSIVE METAL DRIPPAN. RUN 3/4" DRAIN LINE TO ANAPPROVED INDIRECT RECEPTOR.
RUN DISCHARGE LINETO FLOOR DRAIN.(SAME SIZE AS VALVEDISCHARGE)
THERMAL EXPANSION TANK.AMTROL MODEL AST-5 ORAN APPROVED EQUAL.SECURE TANK TO WALL.
1. THE PLUMBING CONTRACTOR IS RESPONSIBLE FOR ALL BACKFLOWDEVICES TO BE INSPECTED BY A CERTIFIED BACKFLOW TECHNICIANBEFORE THE USE OF THE BUILDING POTABLE WATER SYSTEM.
2. THIS BACKFLOW PREVENTER CAN BE INSTALLED IN A VERTICALCONFIGURATION WHEN SPACE IN ROOM IS LIMITED. REFERENCE PLANSFOR CONFIGURATION OR CONTACT THE ENGINEER FOR APPROVAL.
3. THIS SYSTEM IS FOR INDOOR INSTALLATIONS ONLY. THIS VALVE SHALL BEEASILY ACCESSIBLE TO FACILITATE TESTING AND SERVICING. DO NOTINSTALL IN A CONCEALED LOCATION.
CONNECTION SIZEMANUFACTURER / MODEL NUMBER / DESCRIPTION / ADDITIONAL COMMENTS
WASTE VENT TRAP CW HW
DN-1 DOWN SPOUT NOZZLE -- -- -- -- -- JAY R. SMITH FIGURE NUMBER 1775 DOWN SPOUT WITH HINGED PERFORATED COVER AND WALL FLANGE.304 STAINLESS STEEL.
ET-1 EXPANSION TANK -- -- -- 3/4 -- AMTROL THERM-X-TROL ST-12, OR APPROVED EQUAL, NON ASME SERIES THERMAL EXPANSION ABSORBER,ANTIMICROBIAL LINER, AND 5 YEAR WARRANTY.
ACORN MODEL S0420-BF, BARRIER-FREE, WALL MOUNTED, PLASTIC BOWL EYE WASH WITH ABS PLASTIC EYEWASH SPRAY HEAD, WITH TAILPIECE AND TRAP. PROVIDE WITH DUST COVER, UNIVERSAL SIGN, AND ACORNMODEL ET71 THERMOSTATIC MIXING VALVE OR EQUAL, LEAD FREE, WITH TEMPERATURE GAUGE ONOUTLET..
FCO FLOOR CLEANOUT SEEPLANS -- -- -- -- JAY R. SMITH 4020 SERIES WITH ADJUSTABLE TOP AND ABS PLUG. PROVIDE WITH FIGURE NUMBER 9912 FOR
HEIGHT ADJUSTMENT AFTER CONCRETE POUR.
FD-1 FLOOR DRAIN(CONCRETE FLOOR) 2 2 2 -- --
JAY R. SMITH FIGURE NUMBER 2005Y-A05NB: NO-HUB OUTLET, 5" ROUND, NICKEL BRONZE FINISH, WITHADJUSTABLE STRAINER AND TRAP PRIMER. INSTALL TOP OF DRAIN 1/8" BELOW FINISH FLOOR AND CAULKEDGE.
2 2 2 -- -- JAY R. SMITH FIGURE NUMBER 3100Y-12: CAST IRON RECEPTOR, ALUMINUM DOME STRAINER, NICKELBRONZE GRATE, AND TRAP PRIMER. INSTALL TOP OF SINK 1/8" BELOW FINISH FLOOR AND CAULK EDGE.
GCO GRADE CLEANOUT(NON-PAVED AREAS)
SEEPLANS -- -- -- -- JAY R. SMITH 4220 SERIES WITH ABS PLUG.
GCOGRADE CLEANOUT(PAVED AREAS)(VEHICULAR TRAFFIC)
SEEPLANS -- -- -- -- JAY R. SMITH 4250 SERIES, ROUND FLANGED HOUSING WITH HEAVY DUTY CAST IRON COVER. FURNISH WITH
ABS PLUG. COVER TO BE INSCRIBED "SAN".
HB-1HOSE BIBB(EXTERIOR)(NON-FREEZE)
-- -- -- 3/4 -- WOODFORD MODEL 67 - EXPOSED STYLE WITH MODEL 50HA BACKFLOW PREVENTER, 3/4" INLET , ANDCHROME PLATED. PROVIDE WITH TEE KEY AND INSTALL AT 18" ABOVE FINISH GRADE.
HB-2 HOSE BIBB(INTERIOR) -- -- -- 3/4 -- WOODFORD MODEL 26 - EXPOSED STYLE WITH 3/4" INLET, AND CHROME PLATED. PROVIDE WITH METAL
WHEEL HANDLE AND WOODFORD MODEL 50HF BACKFLOW PREVENTER.
LAV-2LAVATORY(WALL MOUNTED)(ADA COMPLIANT)
1 1/2 1 1/2 1 1/4 1/2 1/2
KOHLER KINGSTON MODEL K-2005: VITREOUS CHINA, WALL MOUNTED, HOLES ON 4" CENTERS, AND GRIDSTRAINER. KOHLER CORALAIS MODEL K-15198: 4 1/2" LONG, SINGLE LEVER FAUCET WITH .5 GPM AERATOR.PROVIDE WITH JAY R. SMITH FIGURE NUMBER 0700-Z SUPPORT WITH CONCEALED ARMS AND WATTS SERIESUSG-B THERMOSTATIC MIXING VALVE, ASSE STANDARD 1070 LISTED, BRONZE BODY, INTEGRAL CHECKVALVES, AND SELECTABLE TEMPERATURE RANGE FROM 80°F TO 120°F.
RD/OD-1COMBINATION ROOF/OVERFLOW DRAIN(LOW PROFILE DOME STYLE)(METAL GRATE)
-- -- -- -- -- JAY R. SMITH FIGURE NUMBER 1800Y--CID-RS WITH CAST IRON DOME GRATE AND RAIN SHIELD.
WATTS, SERIES 009 REDUCED PRESSURE ZONE ASSEMBLY, MODEL NO. 009 WITH QUARTER TURN BALLVALVES, BRONZE STRAINER, AND AIR GAP. BRONZE BODY CONSTRUCTION- 1/2" THRU 2", PROVIDE WITHSTRAINER. LEAD FREE. 2 1/2" THRU 10" 957 SERIES.
SA-1 SHOCK ABSORBER(WATER HAMMER ARRESTOR) -- -- -- -- -- JAY R. SMITH FIGURE NUMBER 5005 TO 5050, OR APPROVED EQUAL, SIZED PER FIXTURES SERVED. PROVIDE
AN ACCESS PANEL AND A BALL TYPE SHUT-OFF VALVE UPSTREAM OF SHOCK ABSORBER.
TD-1TRENCH DRAIN(6" WIDE)(HEAVY TRAFFIC RATED)
2 1 1/2 2 -- -- JAY R. SMITH FIGURE NUMBER 9895 6" WIDE TRENCH DRAIN SYSTEM. SLOPE DRAIN SYSTEM WITH INTEGRALMETAL RAIL, PROVIDE WITH END CAPS, OUTLETS, AND CATCH BASIN.
TP-1TRAP PRIMER(PRESSURE ACTIVATED)(1 TO 4 TRAPS)
-- -- -- 1/2" --PRECISION PLUMBING PRODUCTS MODEL CPO-500 WITH DU DISTRIBUTION UNIT IF REQUIRED FOR SERVINGMORE THAN ONE TRAP.APPROVED ALTERNATES: MIFAB, SIOUX CHIEF, SLOAN, AND ZURN
TP-2TRAP PRIMER(FLUSH VALVE PRIMER)(1 TRAP)
-- -- -- 1/2" -- PRECISION PLUMBING PRODUCTS MODEL FVP-1VB WITH VACUUM BREAKER.APPROVED ALTERNATES: MIFAB, SIOUX CHIEF, SLOAN, AND ZURN
U-1 URINAL(ADA COMPLIANT) 2 1 1/2 INT. 3/4 --
KOHLER BARDON MODEL K-4991-ET WALL MOUNTED URINAL WITH 3/4" TOP SPUD.SLOAN REGAL XL MODEL 186-0.5 FLUSHOMETER.INCLUDE BEEHIVE STRAINER AND JAY R. SMITH FIGURE NUMBER 0637 ADJUSTABLE FIXTURE SUPPORT
US-1UTILITY SINK(23" X 21" X 13")(FLOOR MOUNTED)
2 1 1/2 1 1/2 1/2 1/2 FIAT MOLDED STONE MODEL FL-1. PROVIDE WITH A-1 DECK CHROME FAUCET, DRAIN WITH STOPPER, ANDEASY LEVELING LEGS.
WC-1
WATER CLOSET(FLUSH VALVE)(FLOOR MOUNTED)(COMFORT HEIGHT / ADA COMPLIANT)
4 2 INT. 1 --KOHLER HIGHCREST MODEL K-4302 / FLOOR MOUNTED, WITH ELONGATED BOWL.KOHLER LUSTRA MODEL K-4666-C / ELONGATED OPEN FRONT SEAT WITH HINGE.SLOAN REGAL XL MODEL 111 FLUSHOMETER.
WCO WALL CLEANOUT SEEPLANS -- -- -- -- JAY R. SMITH 4472T SERIES WITH CAST BRONZE TAPER THREAD PLUG, STAINLESS STEEL ROUND COVER,
AND A STAINLESS STEEL VANDAL PROOF SCREW.
WH-6WATER HEATER(20 GALLON)(208V-1Ø ELECTRIC)
-- -- -- SEEPLANS
SEEPLANS
BRADFORD WHITE MODEL LE120U3-1NCY, SINGLE ELEMENT, 4.0 KW, 208V/1Ø, 18" DIAMETER, 25" TALL, WITHSIDE AND TOP CONNECTIONS. PROVIDE WITH WALL BRACKET SUPPORT SIZED FOR WEIGHT, SEISMICSTRAPS, AND DRAIN PAN.
NOTES:1. ALL ADA COMPLIANT FIXTURES MUST COMPLY WITH ICC/ANSI A117.1. SEE ARCHITECTURAL PLANS FOR HANDICAPPED FIXTURE DESIGNATIONS, LOCATIONS, CLEARANCES, AND MOUNTING HEIGHTS.
2. ALL EXPOSED HW PIPING, CW PIPING, AND DRAIN LINES BENEATH ALL LAVATORIES AND ALL ADA COMPLIANT SINKS MUST BE INSULATED TO PREVENT INJURY. REFER TO ARCHITECTURAL PLANS. INSULATE WITHMOLDED CLOSED CELL VINYL INSULATION - TRUEBRO, PLUMBEREX, OR EQUAL.
3. PROVIDE P-TRAP PRIMERS FOR ALL FLOOR DRAINS AND FLOOR SINKS. PROVIDE A BALL TYPE SHUT-OFF VALVE UPSTREAM OF PRIMER VALVE. SEE SPECIFICATIONS.
4. SEE SPECIFICATIONS FOR ALTERNATE APPROVED MANUFACTURERS.
5. HIGH EFFICIENCY WATER HEATERS: PROVIDE WITH CONDENSATE NEUTRALIZATION KIT BY JJM BOILER WORKS MODEL JM (OR EQUAL), SIZED PER EQUIPMENT CAPACITY.
6. BACKFLOW PREVENTION: THIS BUILDING IS PROVIDED WITH A BACKFLOW PREVENTION DEVICE ON THE MAIN WATER SERVICE AND REDUCED PRESSURE BACKFLOW PREVENTION ON THE FOLLOWING PIECES OFEQUIPMENT: INTERIOR HOSE BIBBS, EVAPORATIVE COOLER
